Tamko Bathroom Remodeling Nationwide

Tamko Bathroom Remodeling: The Pompano Beach Owner’s Guide

Tamko bathroom remodeling in Pompano Beach typically runs $9,000-$28,000 for a full renovation, and we stock compatible materials across Tamko’s moisture-resistant product lines for same-week scheduling. Most homeowners discover their Tamko bathroom components are failing when grout cracks spread from shower corners, vanity laminate bubbles near the sink edge, or that faint mildew smell won’t clear no matter how often they bleach. In Pompano Beach’s salt-air climate, we’ve learned to look for substrate swelling behind tile first - the humidity gets in faster than owners expect.

Call (754) 714-6540

Which Tamko Models This Applies To

Tamko doesn’t manufacture complete bathroom fixtures; they produce the moisture-resistant building envelope products that protect bathroom assemblies. We’re talking about Tamko TW Metal waterproof underlayment for shower pans, Tamko HydraFlex waterproofing membrane for wet-area walls, and Tamko Elements siding and trim used in bathroom-adjacent exterior walls where vapor drive matters. The critical compatibility gotcha: HydraFlex comes in two mil thicknesses, 40-mil for residential and 60-mil for commercial - we’ve seen Pompano Beach contractors spec the thinner material for steam showers, and it fails at the seams within three years.

Identification is straightforward. TW Metal has a stamped product code and date roll every 24 inches; HydraFlex carries a lot number and thickness marking on the release liner. For OEM versus aftermarket, Tamko’s membrane is proprietary modified asphalt - we’ve tested generic “equivalent” membranes from three suppliers, and two delaminated at the fold lines during our standard 90-day humidity chamber test. We stock genuine Tamko membrane on our trucks, cut fresh from the roll, because the savings on aftermarket rarely survive the first callback.

Signs Your Tamko Bathroom Remodeling Is Failing

• Soft spots near the shower threshold. This means water has breached the membrane at the curb detail, the most common failure point we find in Pompano Beach homes built 2005-2015. The substrate beneath the tile turns to mush while the surface still looks fine - you find it by pressing with a firm thumb.
• Grout cracking in straight lines, not randomly. Straight-line cracking follows movement in the substrate below, usually meaning the TW Metal pan wasn’t lapped correctly at the corners or the pre-slope was omitted. Random cracking is shrinkage; straight lines are structural movement, and it gets worse.
• Baseboard swelling in the room adjacent to the bathroom. Vapor is migrating through an exterior wall that lacks proper Tamko weather barrier integration. In Pompano Beach’s coastal environment, we see this where the bathroom exhaust vent terminates through the wall without sealed flashing.
• Tile “drumming” when you tap it. Hollow sound means the thinset bed has de-bonded from the membrane, often because HydraFlex was installed over damp concrete or green drywall. The tile stays put for months, then one footfall pops it loose.
• Persistent mildew on caulk that was replaced within the year. The caulk isn’t the problem; moisture is wicking through a failed membrane behind the wall. Bleach the surface all you want - the colony lives in the cavity.

Before

After

Replacement Cost & What’s Included

The range depends on three factors: how far the moisture traveled before detection, whether the substrate needs replacement (plywood, cement board, or structural repair), and tile selection - large-format tile requires a flatter substrate and more labor. Our quote includes all materials, labor, permit pulling where required by Pompano Beach building code, and haul-away. Under Clause 1 of The Haven Standard, you receive a written flat price before any demolition starts. The 365-Day Done Right Promise covers workmanship; manufacturer defects fall to Tamko’s product warranty, which we document and register on your behalf.

DIY or Call Us?

There’s a safe middle ground. Homeowners can check for soft spots with a firm press, confirm the exhaust fan moves air with a tissue test, and verify the exterior vent flap closes - these cost nothing and tell you plenty. Where DIY goes wrong is the membrane installation itself. TW Metal requires heat-welded or properly lapped seams at 4-inch minimum overlap; HydraFlex needs factory-approved primer at the correct coverage rate, and both require flood testing for 24 hours before tile goes back. We’ve been called to four Pompano Beach jobs this year where the owner watched a video, bought the roll, and missed the primer step. The repair cost tripled.

We’re not affiliated with Tamko - we’re independent contractors who specify and install their products where they fit the job. If you want a second opinion on another contractor’s scope, bring us their written estimate. We’ll review it line by line at no charge. Measure twice, say it once, show your work.

FAQs