Mr-Glass Roofing Nationwide

Mr-Glass Roofing: The Pompano Beach Owner’s Guide

Mr-Glass roofing repair in Pompano Beach typically runs $400-$1,800 installed, depending on whether we’re matching a single panel section or addressing underlying water intrusion. We stock Mr-Glass-compatible standing seam clips, concealed fastener hardware, and color-matched Kynar-coated panels for the most common series installed in South Florida since 2015. Most calls start the same way: a homeowner spots rust streaks near the rake edge after a heavy rain, or notices the panel has started to oil-can (that wavy, loose appearance) in the afternoon heat. In Pompano Beach, the salt air off the Intracoastal accelerates fastener corrosion, and the thermal cycling between 90-degree days and 75-degree nights works the clip system loose over seven to ten years. We see it regularly in the older ranch homes between Atlantic Boulevard and McNab Road, where original Mr-Glass installs are hitting that window now.

Call (754) 714-6540

Which Mr-Glass Models This Applies To

Mr-Glass has produced three primary standing seam lines relevant to Pompano Beach residential work: the SL-150 (1.5″ snap-lock, 16″ panel width), the SL-200 mechanical seam (2″ rib height, 18″ width), and the earlier SL-100 snap-lock discontinued around 2014 but still common on homes built during the 2008-2012 construction lull. The clip spacing, rib profile, and male/female leg geometry differ enough that mixing series hardware guarantees a leak. Check the panel edge: snap-lock panels have a simple folded seam you can lift slightly with a flat bar; mechanical seam panels show a double-folded, crimped joint that requires a seamer tool to release.

We carry OEM Mr-Glass clips and fasteners, but also source from McElroy and ATAS when the original spec has been superseded or when lead times stretch past two weeks. The aftermarket equivalent must match the clip gauge (typically 26-gauge for SL-150, 24-gauge for SL-200) and the thermal break pad material, not just the dimensional profile. One compatibility gotcha: Mr-Glass switched from stainless to zinc-aluminum coated clips in 2018 for cost reasons, and the newer clips corrode faster within three miles of salt water. We stock both and will tell you which was original to your roof.

Signs Your Mr-Glass Roofing Is Failing

• Panel oil-canning or waviness. This is the metal relieving stress from improper clip spacing or thermal expansion against a fixed fastener. In Pompano Beach’s climate, the daily expansion-contraction cycle is severe, and once a panel starts oil-canning, the fatigue cracking follows within two to three years.
• Rust streaks at panel ends or clip lines. The Kynar coating fails first at cut edges and fastener penetrations. Salt air wicks into the gap between clip and panel, and the galvanic reaction between dissimilar metals does the rest. We see this worst on east-facing slopes catching the onshore flow.
• Lifted or displaced panels after wind events. Mr-Glass snap-lock panels rely on wind clips at the eave and rake; if the clip screws have backed out or the thermal break has compressed, the panel lip can release. Tropical Storm-force gusts will test any marginal installation.
• Interior staining at ridge or valley locations. Standing seam is only as good as the flashing integration. Mr-Glass uses a separate Z-bar at ridge transitions, and the butyl tape beneath it has a 12-15 year service life in Florida UV before it hardens and channels water inward.
• Noisy expansion pops during morning heating. A properly clipped panel slides silently in its bracket. Popping or ticking means a fastener is binding, creating point-load stress that will eventually crack the panel rib or pull through the clip ear.

Before

After

Replacement Cost & What’s Included

Mr-Glass roofing repair in Pompano Beach falls within our standard Roof Repair: $400-$1,800 range. A single panel replacement with matching clip hardware runs $400-$750. Sectional repair involving three to five panels, underlying underlayment, and ridge flashing replacement pushes $1,200-$1,800. Full Mr-Glass roof replacement, when the clip system is too compromised for spot repair, aligns with our Roof Replacement: $8,000-$20,000 range for typical Pompano Beach footprints of 1,800-2,800 square feet.

Every written quote itemizes parts (panel, clips, fasteners, sealant, underlayment patch), labor hours, and disposal. Under Clause 1 of the Haven Standard, that price is fixed; if we find additional damage during removal, we document it with photos, write a change order, and nothing proceeds until you sign. The 365-Day Done Right Promise covers the repair workmanship, and we register any panel finish warranty with Mr-Glass on your behalf.

DIY or Call Us?

There’s a safe middle ground here. A homeowner can walk the roof with binoculars from a ladder (never on the panels themselves - the oil-canning risk is real, and the surface is slick when dew forms) and confirm the panel series from the rib profile. You can also check the interior for staining patterns and photograph any rust streaks for our review.

What you should not attempt: removing a standing seam panel requires releasing the seam without creasing the adjacent panel, a technique that takes practice to avoid turning a $600 repair into a $3,000 replacement. The clips are under tension and the panel edges are sharp enough to slice through work gloves. We carry the portable seamer, the color-matched touch-up pens, and the clip inventory on our truck. Call (754) 714-6540 and we’ll photograph what we find, show you the scope, and give you the written price before anyone touches a tool. Measure twice, say it once, show your work.

FAQs