KraftMaid Roofing Nationwide

KraftMaid Roofing: The Pompano Beach Owner’s Guide

KraftMaid-compatible roofing parts in Pompano Beach typically run $400-$1,800 installed, and we stock the common failure items on our trucks for same-day replacement. Most homeowners discover the issue during our wet season, when a lifted ridge vent or cracked flashing that held through the dry months finally lets water into the soffit line. If you’re seeing stains on your ceiling after a May thunderstorm, the part that failed probably started degrading months earlier.

Call (754) 714-6540

Which KraftMaid Models This Applies To

KraftMaid built roofing components for three distinct product tiers: the standard builder-grade line (2002-2015), the mid-grade “Select” series with upgraded underlayment specs, and the short-lived “Premium WeatherShield” line sold primarily through Florida distributors from 2008-2012. The critical compatibility gotcha: WeatherShield used a proprietary 6-inch ridge vent profile that standard 7-inch replacements will not seat into without visible gap or forced compression, which voids any meaningful warranty on the repair.

To identify your series, check the underside of any original soffit vent for a stamped date code and “KM-” prefix. The Select series carried a secondary “SL” stamp. For OEM-versus-aftermarket, we’ve found that KraftMaid’s original drip edge (galvanized, 26-gauge, with the signature hemmed return) outlasts generic equivalents by roughly 30% in Pompano Beach’s salt-air environment. We stock both and will show you the physical difference before quoting. Cambria, Silestone, and Kohler parts cross our truck too, but KraftMaid roofing hardware has its own sizing logic that doesn’t translate.

Rowan Construction Group Pompano Beach is an independent service provider with no affiliation to KraftMaid Corporation.

Signs Your KraftMaid Roofing Is Failing

• Water stains appearing as straight lines on your ceiling. This usually traces to a failed ridge vent end cap, where KraftMaid’s snap-fit design loses tension after 8-12 years of thermal cycling. The gap opens just enough to channel wind-driven rain in a concentrated stream.
• Granules collecting in gutters after every storm, but shingle tabs look intact. The KraftMaid starter strip on early Select series used an adhesive that degrades faster than the shingle itself. The roof isn’t failing dramatically; it’s shedding protection incrementally, which is harder to spot and more expensive to ignore.
• Soffit vents that whistle or rattle in sustained winds. The mounting clips on builder-grade units fatigue at the bend point. In Pompano Beach, we see this accelerate when homeowners pressure-wash from below, forcing water into the clip cavity.
• Flashing that has pulled ¼ inch or more from the wall plane. KraftMaid’s step flashing incorporated a friction-fit counter-flange that relies on precise shingle compression. Once that compression loosens, capillary action draws water behind the brick or stucco.
• Daylight visible through the attic near chimney or vent stacks. The rubber collar on KraftMaid pipe boots cracks predictably at year 10-14 in Florida UV. By the time you see light, the adjacent decking has likely absorbed enough moisture to require sistering, not just a boot swap.

Before

After

Replacement Cost & What’s Included

What drives the spread: accessibility (steep pitches add labor hours), whether the substrate needs repair after the part comes off, and whether your original KraftMaid component was part of a system that requires matched replacement. A ridge vent swap on a walkable 4/12 pitch runs toward the lower end; a WeatherShield vent on a 10/12 with degraded decking beneath it moves toward the upper bound.

Every quote we write in Pompano Beach is flat-priced with parts and labor itemized, and it’s delivered before anyone touches a ladder. Under Clause 1 of the Haven Standard, that written price is binding. The 365-Day Done Right Promise covers the workmanship. No change order gets signed unless you request a scope change, and no work proceeds on that change until the paperwork is done. Grant Rowan started this discipline in 2007, and it’s why our projects finish within a few percent of the number we first wrote down.

DIY or Call Us?

Here’s what you can safely check from the ground or a stable interior ladder: confirm the stain location against your roof plan, photograph any visible vent or flashing from the attic side, and note whether the damage correlates with a specific weather event. That documentation helps us quote accurately and saves you a trip charge.

Here’s where DIY goes wrong: KraftMaid ridge vents require release of multiple shingle courses to remove without tearing, and the replacement must be hand-nailed to manufacturer spacing to maintain wind uplift rating. Step flashing replacement involves working at the roof-wall intersection with a pry bar near live electrical service entrances. The fall risk is real, and the permit requirement for structural roofing work in Broward County means an unpermitted repair can complicate your sale later. We pull permits as standard, include the documented photo record, and background-check every technician who shows up. Call (754) 714-6540 to schedule your free estimate.

FAQs