Jerith Kitchen Remodeling Nationwide

Jerith Kitchen Remodeling: The Pompano Beach Owner’s Guide

Jerith kitchen remodeling in Pompano Beach runs $14,000-$45,000 for a full project, with cabinet installation alone at $4,000-$13,000 and countertop installation at $2,000-$6,500. We stock Jerith-compatible components across all major series and can typically source same-day what we don’t carry on the truck. Most Pompano Beach owners first notice a problem when cabinet doors won’t stay aligned after a humid summer, or when drawer glides start binding - both signs that the original hardware or substrate is giving out in Florida’s salt-air climate.

Call (754) 714-6540

Which Jerith Models This Applies To

Jerith produces three main cabinet lines that circulate in South Florida: the Classic Series (face-frame construction, 3/4-inch plywood box), the Contemporary Series (frameless European-style, 5/8-inch melamine-over-particleboard), and the Premier Series (solid wood dovetail drawers, soft-close undermount glides). The part you need depends on which box you’re opening.

Classic Series units carry a foil label inside the door frame with a six-digit SKU starting in “CL”; Contemporary labels start “CT” and sit on the hinge side of the cabinet wall. Premier Series uses an engraved stamp on the drawer box itself. If the label’s gone, measure the wall thickness with the door open: 3/4 inch means Classic or Premier, 5/8 inch means Contemporary. The hinge bore pattern differs too - 35mm cup depth on Classic, 40mm on Contemporary - so ordering the wrong hinge set means drilled holes that don’t seat flush.

We source OEM Jerith hardware direct from their distribution in Hialeah Gardens, but for drawer glides and hinge sets we also stock Blum and Salice equivalents that meet the same cycle-test ratings at lower cost. The decision comes down to whether you’re matching existing finish exactly or replacing a whole run. Under Clause 1 of the Haven Standard, we put both options in writing with the price difference shown before you decide.

Signs Your Jerith Kitchen Remodeling Is Failing

• Doors sag or won’t stay closed. The hinge cup has wallowed out in the particleboard, or the soft-close piston has leaked its hydraulic fluid. In Pompano Beach, salt air accelerates corrosion on the hinge pin even indoors, so we see this on units within eight years that should last twelve.
• Drawers bind, stick, or fall off the track. The glide roller has flattened or the epoxy-coated steel ball bearing race has rusted. Jerith’s Contemporary Series used a lighter-duty 75-pound-rated glide through 2019; if your kitchen sees heavy pots, that’s underspecified for actual use.
• Laminate surfaces bubble or delaminate at edges. Moisture has penetrated the substrate, usually from a sink seal failure or dishwasher steam venting backward. The particleboard swells, the laminate releases, and the repair requires either a new door/drawer front or a full countertop-to-backsplash assessment if water reached the cabinet box.
• Shelves bow or crack. Standard Jerith shelves are 1/2-inch melamine over particleboard rated for 35 pounds per linear foot. Owners often overload them with small appliances; the fix is a 3/4-inch plywood upgrade or added center support, which we note in the written scope.
• Cabinet box separates at corners. The staple-and-glue joint has failed, typically from repeated humidity cycling. Florida’s wet season pushes indoor relative humidity past 70 percent even with AC; the expansion-contraction loosens the bond. This is structural and needs reassembly or replacement, not a surface fix.

Before

After

Replacement Cost & What’s Included

The range spreads wide because “remodeling” covers everything from swapping cabinet fronts on existing boxes to stripping to studs and rebuilding. What moves a Pompano Beach job toward the top: relocating gas or water lines, adding an island where none existed, or bringing a 1970s kitchen up to current Florida Building Code for electrical outlet spacing. We itemize every line in the written quote - no lump-sum mystery - and no work proceeds on any change until the change order is signed, which is how we’ve kept projects within a few percent of the agreed number since 2007.

Every Jerith-compatible installation carries our 365-Day Done Right Promise: if the alignment drifts, the glide fails, or the finish delaminates, we make it right. The warranty is printed on the quote, not implied.

DIY or Call Us?

There’s a safe middle ground here. An owner can check hinge screw tightness with a Phillips head, confirm that sagging doors still sit square in the frame (if they’re twisted, the hinge cup is damaged, not just loose), and photograph any water staining for documentation. What we don’t recommend: drilling new hinge bores with a Forstner bit freehand, cutting countertop substrate to fit a replacement cabinet, or attempting electrical relocation for under-cabinet lighting without verifying GFCI protection. Misaligned hinge cups mean doors that never seal; improper countertop support means cracks at the seam within months.

Rowan Construction Group Pompano Beach is an independent service provider - not affiliated with Jerith - and we’ve handled enough of their product lines to know where the tolerances run tight. If you’re matching existing finish or unsure which series you own, call (754) 714-6540. We’ll schedule a free estimate, identify the part on site, and put the installed price in writing before any work starts.

FAQs