CWS Bathroom Remodeling Nationwide

CWS Bathroom Remodeling: The Pompano Beach Owner’s Guide

CWS bathroom remodeling in Pompano Beach typically runs $9,000-$28,000 for a full renovation, with smaller bath refreshes starting around $5,000. We stock and install CWS-compatible fixtures, enclosures, and hardware across their product lines, and we carry common CWS replacement components on our trucks for same-day repair calls. Most Pompano Beach homeowners realize something’s wrong when a shower door won’t track straight, a frameless enclosure starts leaking at the sill, or a bypass roller seizes after years of salt-air exposure.

Call (754) 714-6540

Which CWS Models This Applies To

CWS, or Custom Window Systems, manufactures bathroom enclosures and fixtures primarily through their CWS Shower Door and CWS Bath lines sold through Florida distributors. The model identifier is usually etched on the hinge bracket or stamped on the bottom rail - a four-digit number followed by a series letter (A through D denoting the track profile). The A-series uses a 3/4-inch wall jamb; the D-series, introduced in 2019, moved to a 1-inch jamb with a deeper drip edge for Florida’s driving rains.

We see the most service calls on CWS units installed between 2012 and 2018, when the company used a nylon roller with a brass bushing that corrodes in coastal humidity. The current OEM roller assembly is all-stainless, but the mounting hole spacing (2-1/8 inches center-to-center) didn’t change, so the upgrade fits older frames. We also source quality aftermarket equivalents from CRL and Prime-Line when OEM lead times stretch past a week - the spec matches, the warranty is comparable, and the price difference usually runs 15-20 percent lower. If your CWS unit has the older brass-bushing rollers, we recommend replacing all four at once; the wear pattern is consistent, and the labor to open the frame is the same whether we swap one or all.

Signs Your CWS Bathroom Remodeling Is Failing

• Door hangs crooked or drags on the sill. The roller wheels have flattened or the axle bracket has bent from repeated impact against the door stop. In Pompano Beach, salt air accelerates the bearing corrosion that causes this misalignment, and we see it most often on east-facing bathrooms that get morning sun followed by afternoon humidity.
• Water pools outside the shower after every use. The vinyl sweep at the bottom of the door has hardened or torn, or the sill dam has lost its seal against the tile. CWS sills from the 2015-2019 production run used a softer vinyl that degrades faster in Florida’s UV exposure.
• Glass rattles in the frame when the door closes. The rubber glazing gaskets have shrunk or the silicone bedding has failed. This is a safety issue - tempered glass needs continuous support around its perimeter - and it’s one we address immediately when we find it.
• Handle or hinge feels loose though screws are tight. The aluminum frame extrusion has wallowed out at the mounting hole, usually from over-torquing during a previous DIY repair. We fix this with a helicoil insert or by relocating the hardware to virgin metal, not by longer screws that just enlarge the problem.
• Frameless enclosure leaks at the wall joint. The silicone seal has failed, or the wall clips were installed without the required 1/16-inch shim gap that allows for frame flex. CWS frameless systems require 100-percent silicone at all glass-to-metal and glass-to-tile joints; latex or hybrid products don’t hold up to the thermal cycling in a steam shower.

Before

After

Replacement Cost & What’s Included

A CWS shower door repair in Pompano Beach typically runs $300-$850 depending on what’s failing. Roller replacement alone is usually $180-$340; a full door removal, re-silicone, and rehang runs $550-$850 if the glass and hardware are salvageable. For a complete CWS enclosure replacement, figure $2,500-$6,500 installed, with frameless systems at the higher end.

What drives the range: the condition of the surrounding tile (we won’t reinstall over failed substrate), whether the existing opening is plumb and square (older Pompano Beach condos often aren’t), and whether we’re matching a discontinued CWS profile or can use current stock. Every repair quote includes parts, labor, removal and disposal, new silicone throughout, and a written 365-Day Done Right Promise. Under Clause 1 of the Haven Standard, that price is fixed - no change orders, no surprises. We also provide a documented photo record of the condition we found and what we corrected, included as standard.

DIY or Call Us?

There’s safe checking, and then there’s the work itself. A homeowner can verify the model number, measure the opening width at three points (top, middle, bottom - they often differ), and inspect the sweep for visible damage. What we don’t recommend: removing a frameless glass panel yourself. Tempered glass weighs 6-8 pounds per square foot, a 36-by-72-inch panel runs 100-plus pounds, and the edge chips that lead to spontaneous fracture aren’t always visible. We’ve been called to three jobs in Pompano Beach where a dropped panel shattered across the bathroom, and the cleanup cost exceeded what professional removal would have run.

Same for silicone replacement on frameless units - the bead geometry matters, and CWS warranties require neutral-cure 100-percent silicone applied to clean, dry surfaces within specific temperature ranges. If the door is sticking, leaking, or showing any of the symptoms above, call (754) 714-6540. We’ll diagnose it, quote it in writing, and fix it without the guesswork.

FAQs

How long does a CWS shower door typically last in Pompano Beach?

With proper maintenance, 15-20 years, though the rollers and sweeps need replacement every 5-7 years in coastal humidity. The salt air and UV exposure here are harder on seals and hardware than inland Florida climates. Call (754) 714-6540 for an exact quote - estimates are free.

Can my CWS enclosure be repaired, or does it need full replacement?

Most hardware failures - rollers, sweeps, hinges, seals - are repairable if the glass is intact and the frame isn’t corroded. We replace only when the aluminum extrusion is pitted through, the glass is damaged, or the model has been discontinued and parts are unavailable. Call (754) 714-6540 for an exact quote - estimates are free.

How long does a CWS roller or sweep replacement take?

Typically 90 minutes to 2 hours for a standard bypass door, assuming the frame is square and the surrounding tile is sound. Frameless enclosures take longer - 2-3 hours - because every panel must be removed to access the hardware. Call (754) 714-6540 for an exact quote - estimates are free.

Do you stock CWS parts on your trucks?

We carry rollers, sweeps, hinges, and silicone for the most common CWS series, and we can source same-day from our Pompano Beach suppliers for anything we don’t have. If your model is discontinued, we’ll tell you upfront and quote a compatible replacement rather than chase parts that don’t exist. Call (754) 714-6540 for an exact quote - estimates are free.

Rowan Construction Group Pompano Beach is an independent service provider and is not affiliated with CWS. We also stock and install parts for KraftMaid, Cambria, and Silestone products.

Ready to get your CWS bathroom back to working right? Call (754) 714-6540 to schedule your free estimate. We’ll put the number in writing before anyone picks up a tool - that’s Clause 1 of the Haven Standard, and it’s how we’ve kept projects within a few percent of the agreed price across 4,000-plus jobs since 2007. Measure twice, say it once, show your work.

Written by Grant Rowan, Owner, Rowan Construction Group Pompano Beach at Rowan Construction Group Pompano Beach, serving Pompano Beach and nearby areas.