Atlas Kitchen Remodeling Nationwide

Atlas Kitchen Remodeling: The Pompano Beach Owner’s Guide

Atlas kitchen remodeling in Pompano Beach typically runs $14,000-$45,000 for a complete project, with cabinet installation from $4,000-$13,000 and countertop installation from $2,000-$6,500. We stock Atlas-compatible cabinet hardware, drawer systems, and soft-close hinge sets on our trucks, and most Atlas part replacements can be scheduled within 48 hours. Homeowners usually discover a problem when a drawer glide seizes, a soft-close hinge loses its damping, or a cabinet box shows swelling at the sink cabinet floor - the moisture barrier on older Atlas sink bases was a single sheet of melamine, not the upgraded marine-grade plywood used after 2019.

Call (754) 714-6540

Which Atlas Models This Applies To

Atlas Cabinetry produces three residential lines that have circulated through Pompano Beach since the mid-2000s: the Builder Series (discontinued 2016), the Designer Series (2010-present), and the Estate Collection (2018-present). The Builder Series used a ½-inch particleboard core with thermofoil facing; the Designer Series upgraded to ¾-inch furniture-grade plywood with a veneer or painted finish; the Estate Collection uses ¾-inch plywood with dovetail drawer boxes and full-extension undermount glides rated to 100 pounds.

To identify your line, check the hinge cup stamp (Blum or Grass for Designer and Estate; generic press-fit for Builder) or the drawer box joint (stapled butt joint on Builder, half-blind dovetail on Estate). The critical compatibility gotcha: Atlas switched from 35mm cup hinges to a proprietary 40mm cup in 2021 for select Estate SKUs, and the hole pattern does not retrofit without a new door bore. We carry both cup sizes and the adapter plates, but most Pompano Beach suppliers stock only the 35mm. Rowan Construction Group Pompano Beach is an independent service provider, not affiliated with Atlas.

For OEM versus quality aftermarket, we source Atlas-spec Blum Tandem glides and Salice hinges through our distributor in Fort Lauderdale, but we also stock Knape & Vogt heavy-duty replacements where the original glide channel has fatigued. The aftermarket glide carries the same 75-pound dynamic load rating and costs 30% less; we note the substitution on the written quote so you know what you’re getting.

Signs Your Atlas Kitchen Remodeling Is Failing

• Drawer sticks or drops when loaded. The Tandem glide’s nylon roller has worn flat, or the steel ball bearing cage has corroded from salt air infiltration. In Pompano Beach, we see this accelerate within three blocks of the Intracoastal where garage and kitchen humidity cycles are sharper.
• Cabinet door hangs crooked or won’t stay closed. The soft-close hinge’s hydraulic cylinder has leaked its damping fluid, or the mounting plate screw holes have wallowed out in the particleboard. Builder Series boxes are especially prone to screw pullout; we repair with hardwood dowel inserts, not longer screws that chew the core wider.
• Sink cabinet floor is soft or discolored. The melamine moisture barrier has failed at the seam, letting dishwasher or sink drain leaks wick into the particleboard. Atlas addressed this in 2019 with a full plywood sink base floor; older units need the floor replaced, not just dried.
• Corner lazy Susan binds or tilts. The polymer tray has cracked at the hub, or the center shaft has bent from uneven loading. The Atlas OEM replacement is a two-week order; we stock a Rev-A-Shelf equivalent that matches the 28-inch shaft height and ¾-inch shelf thickness.
• Painted finish is checking or peeling at door edges. Thermofoil delamination on Builder Series, or UV degradation on early Designer Series painted doors before Atlas switched to a catalyzed conversion varnish in 2015. Pompano Beach’s south-facing kitchens without window film show this two to three years sooner than shaded exposures.

Before

After

Replacement Cost & What’s Included

What drives the range: box construction material (particleboard vs. plywood), door style and finish complexity, and whether we are replacing within existing footprints or reconfiguring the layout. A written quote from Rowan Construction Group Pompano Beach itemizes every line - cabinets, hardware, installation, disposal - before any work starts. Under Clause 1 of the Haven Standard, that written price is fixed; no change proceeds without a signed change order. Every Atlas part replacement carries our 365-Day Done Right Promise: if the glide binds, the hinge sags, or the finish fails, we make it right. The documented photo record of your cabinet condition, included standard, is what you leave with.

DIY or Call Us?

An owner can safely check the hinge cup diameter with a tape measure, confirm the drawer box joint type, and photograph any water damage for documentation. What goes wrong in DIY: boring a 40mm cup into a door drilled for 35mm, which blows out the back face; installing a glide without shimming for an out-of-square cabinet, which loads the mechanism unevenly and voids the warranty; or missing the swollen particleboard under a seemingly intact laminate skin, which collapses the repair in six months.

We don’t recommend homeowner replacement of wall-mounted upper cabinets - the French cleat or screw rail must hit stud, and a 36-inch wall cabinet with dishes runs 150 pounds. Call (754) 714-6540 to schedule your free estimate. We’ll measure twice, say it once, show your work.

FAQs