Unilock Fence Installation Nationwide

Unilock Fence Installation: The Pompano Beach Owner’s Guide

Unilock fence installation in Pompano Beach typically runs $3,500-$9,000 for a complete vinyl or aluminum system, depending on linear footage, soil conditions, and whether we’re anchoring into the sandy loam common east of Dixie Highway or the denser ground near the Intracoastal. Most Pompano Beach homeowners discover their fence is failing when posts lean after a summer storm, panels pull from corroded brackets, or gates sag enough to drag. We stock Unilock-compatible posts, rails, and hardware for same-day repair on most configurations.

Call (754) 714-6540

Which Unilock Models This Applies To

Unilock manufactures fence systems under several series names, and the part you need depends on which generation is in your yard. The Unilock Classic line, common in Pompano Beach subdivisions built between 2005 and 2015, uses 5-inch square posts with routed rail pockets. The newer Unilock Select series switched to 4-inch posts with a different bracket spacing, 3/4 inch offset from Classic. Check the post cap: Classic caps snap on with internal tabs; Select caps thread onto a molded boss. The rail profile also differs, Classic being a true 1.5-inch by 5.5-inch rectangle, Select slightly tapered at the ends.

We carry both OEM Unilock components and quality aftermarket equivalents from Fortress and Ameristar where the spec matches. The aftermarket rails we use are galvanized steel with a polyester powder coat rated to 3,000 hours salt spray, which matters in Pompano Beach’s coastal air. One compatibility gotcha: Unilock’s aluminum series from 2012-2014 used a proprietary bracket hole pattern that standard aftermarket hardware won’t match without drilling. We check this on site before quoting.

Signs Your Unilock Fence Installation Is Failing

• Posts lean or wobble at the base. In Pompano Beach, the sandy soil east of Federal Highway drains fast but doesn’t hold a post tight. Water washes fine particles from around the concrete footing during our heavy summer rains, creating a void the post rocks in. We see this most on 6-foot privacy sections that catch wind like a sail.
• Rails pull out of post pockets or brackets. Unilock’s routed vinyl posts rely on friction and a single screw. After eight to ten years of thermal cycling, 90-degree summers to 50-degree winter nights, the vinyl relaxes its grip. The rail slips, the screw tears through, and the panel goes slack.
• Gate sags and drags at the latch end. The diagonal brace cable or compression member loosens, or the hinge post itself settles. On aluminum gates, the hinge bolts wallow out their holes. On vinyl, the steel insert inside the gate frame corrodes and expands, bowing the rail.
• Corrosion blooms on aluminum hardware. Pompano Beach’s salt air attacks the zinc plating on brackets and screws first, showing white or rust-colored streaks. Once the plating is breached, the base metal pits quickly. We replace with 316 stainless hardware within a mile of the coast.
• Panels rattle in wind or make clicking sounds. The U-channel or bracket that holds the panel has cracked or the thermal expansion gap has closed up completely. Vinyl expands roughly 1/8 inch per 10 feet per 20 degrees Fahrenheit; without proper gap, something has to give.

Before

After

Replacement Cost & What’s Included

The range depends on three factors: access (can we get a mini-excavator to the line, or are we hand-digging between a pool cage and seawall?), soil stability (sandy loam needs a wider footing), and whether we’re matching existing faded color or replacing a full run. Every quote is a flat written price with line-item scope before work starts. Under Clause 1 of The Haven Standard, that number does not change unless you sign a change order. Our 365-Day Done Right Promise covers the installation; hardware carries the manufacturer’s warranty, which we register for you.

DIY or Call Us?

There’s a short list of what a Pompano Beach homeowner can safely check without tools: confirm the post is loose by hand pressure, look for visible cracks in vinyl rails, and note whether gate hinges are tight to the post. Beyond that, fence work has genuine hazards. Posts set in concrete weigh 80 to 120 pounds; digging them out risks back injury. Aluminum rails have sharp edges after cutting. And any fence within 10 feet of an electrical service line requires a utility locate by law, which we coordinate through Sunshine 811.

Where DIY goes wrong is the footing depth. Florida Building Code requires 24 inches minimum for a 6-foot fence in Broward County, but we’ve pulled out homeowner repairs set at 16 inches that heaved in the first freeze-thaw cycle. We measure twice, say it once, show our work: the photo record you receive documents footing depth, plumb, and hardware torque spec. Call (754) 714-6540 to schedule your free estimate.

FAQs