Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Belgard Windows & Doors: The Pompano Beach Owner’s Guide
Belgard window and door parts in Pompano Beach typically run $180-$620 installed depending on the component, and we stock the most common Belgard hardware, seals, and sash balances on our trucks for same-day replacement. Most Pompano Beach homeowners discover a problem when they feel salt-air draft around the frame, the sash won’t stay open, or the multipoint lock won’t engage fully. The combination of coastal humidity, UV exposure, and the occasional tropical storm stress-test every component harder than inland installs.
Which Belgard Models This Applies To
Belgard has produced several window and door series over the past two decades, and the part you need depends on the generation. The 300 Series vinyl double-hung and 500 Series casement windows, common in South Florida builds from 2008-2018, use a specific 5/8-inch diameter coil balance that differs from the 3/4-inch version found in the later 600 Series. The multipoint locking hardware on Belgard’s French and sliding patio doors changed suppliers around 2015, so the faceplate hole spacing shifted from 7-1/4 inches to 7-1/2 inches. That’s a compatibility gotcha we’ve seen trip up ordering: the lock mechanism looks identical until you try to mount it.
To identify your part, check the etched code in the glass corner (format: BLD-YY-MMDD-PLANT) or the stamped label on the frame edge. We carry both OEM Belgard components and quality aftermarket equivalents from Truth Hardware and Amesbury for balances, and Hoppe for door hardware. OEM guarantees exact fit; aftermarket often runs 20-30% less and carries the same 10-year warranty. For Pompano Beach’s salt-air environment, we generally recommend OEM on anything that seals or locks, and aftermarket on mechanical wear items like balances where the spec matches.
Signs Your Belgard Windows & Doors Is Failing

- Sash drops or won’t stay open. The coil balance, a spring-loaded counterweight inside the frame jamb, has fatigued. In Pompano Beach’s heat and humidity, these typically last 8-12 years, shorter than the 15-year inland average.
- Draft around the frame even when closed. The compression seal or bulb gasket has hardened or torn. Salt crystallization accelerates this; we see it first on west-facing units that bake afternoon sun.
- Condensation between glass panes. The insulating glass unit (IGU) seal has failed, allowing moist air into the cavity. This is not repairable; the entire IGU gets replaced.
- Multipoint lock sticks or won’t fully engage. The gearbox has corroded or the shootbolts are out of alignment. Often starts with one point failing before the others follow.
- Frame corner gaps or visible warping. Vinyl expands and contracts; after years of thermal cycling, corners can separate or the sill can bow. This compromises the weather barrier and needs structural assessment.
Before
AfterReplacement Cost & What’s Included
| Component | Parts + Labor Range | Typical Time |
|---|---|---|
| Coil balance (per sash) | $180-$290 | 45-60 min |
| Compression seal replacement | $220-$380 | 1-1.5 hrs |
| IGU replacement (per lite) | $340-$620 | 1.5-2.5 hrs |
| Multipoint lock hardware | $260-$480 | 1-2 hrs |
| Sash or frame repair | $280-$550 | 1.5-3 hrs |
The range reflects part grade (OEM vs. aftermarket), accessibility, and whether we need to pull trim or siding to reach the component. Every quote is a flat written price with line-item parts and labor before work starts, under Clause 1 of The Haven Standard. Our 365-Day Done Right Promise covers the installation and the part. For context, full Window Replacement in Pompano Beach runs $4,500-$15,000, and Impact Window Installation runs $8,000-$25,000 if the frames themselves have reached end of life.
DIY or Call Us?

There’s a safe middle ground and a hard stop. An owner can check the etched glass code, photograph the failed component, and verify the lock points engage fully by feel. What we don’t recommend: removing a sash with a failed balance (the counterweight is under tension and can release suddenly), or drilling out a corroded lock gearbox (you’ll damage the mortise pocket and turn a $280 repair into a $600 one). The multipoint locks on Belgard doors also interface with the sill threshold; misalignment here affects drainage and voids the water intrusion warranty. We’re background-checked, uniformed, and carry a documented photo record on every visit so you see what we found and what we did. Call (754) 714-6540 to schedule your free estimate.
FAQs
In Pompano Beach’s coastal climate, balances last 8-12 years, seals 10-15 years, and IGUs 15-20 years if the original seal held. West and south exposures age faster due to UV load. Call (754) 714-6540 for an exact quote on replacement - estimates are free.
Seals and balances are replace-only; IGUs cannot be resealed in the field. Lock gearboxes can sometimes be lubricated and realigned if caught early, but once corrosion sets in, replacement is the reliable fix. Call (754) 714-6540 for an exact quote - estimates are free.
Most single-component replacements finish in 1-2 hours. IGU replacement takes longer because the sash must be disassembled, reglazed, and cured. We schedule with a two-hour window and a text confirmation 30 minutes out. Call (754) 714-6540 to schedule your free estimate.
We stock the five most common balances, seals, and lock sets for Belgard’s 300, 500, and 600 Series. Less common hardware or discontinued lines we source within 24-48 hours through our supplier network. Call (754) 714-6540 to confirm availability for your model.
Written by Grant Rowan, Owner, Rowan Construction Group Pompano Beach at Rowan Construction Group Pompano Beach, serving Pompano Beach and nearby areas.







Before
After
Before
After
Before
After