Jerith Roofing Nationwide

Jerith Roofing: The Pompano Beach Owner’s Guide

Jerith aluminum roofing components in Pompano Beach typically run $600-$2,500 installed depending on whether you’re replacing individual panels, ridge caps, or an integrated flashing assembly. We stock Jerith-compatible panels and fasteners on our trucks, and most replacements are completed in a single visit. Most Pompano Beach homeowners discover the problem after a hard rain: water stains on the patio ceiling, a panel that rattles loose in the afternoon sea breeze, or corrosion blooming around the fasteners where the coastal salt air has found a gap.

Call (754) 714-6540

Which Jerith Models This Applies To

Jerith manufactured several aluminum roofing systems over the decades, and the part you need depends on the series stamped on the underside of your existing panel. Look for a small embossed code near the panel edge: Series 2000, 3000, or the heavier-gauge 5000 line. The 2000 series uses a 3/4-inch snap-lock rib on 12-inch centers; the 3000 and 5000 lines moved to a 1-inch standing seam with a concealed clip system that is not interchangeable. If your panels were installed before 2010, you likely have the 2000 series, which Jerith discontinued in 2012. We source OEM-grade 0.032 aluminum from the same mill Jerith used, or we can match with a quality aftermarket panel if the original profile is no longer produced. The critical spec is the rib height and the clip spacing, not the brand name on the box. Bring us a 6-inch sample cut from a damaged panel and we’ll measure the gauge and profile on site.

Signs Your Jerith Roofing Is Failing

• Water dripping at the ridge or panel seams. The butyl tape between overlapping panels has dried out in the Florida sun, usually after 12-15 years. Once the seal fails, wind-driven rain pushes straight through the lap joint.
• White powder or pitting around fasteners. Galvanic corrosion between the aluminum panel and the steel fastener is accelerated by salt air. In Pompano Beach, we see this inside of 8 years on homes within a mile of the Intracoastal.
• Panel oil-canning or waviness between supports. The aluminum has exceeded its fatigue limit from thermal expansion cycling, 160-plus days a year above 85 degrees. The panel is not structurally failed yet, but the stress fractures will follow.
• Daylight visible through the ridge cap ends. The foam closure strips have degraded to dust, which is normal after a decade. Without that seal, driving rain and wasps enter the same hole.
• Staining on the soffit or fascia directly below a valley. The Jerith valley pan has separated at the seam or the diverter has cracked at the bend. This is the most expensive leak to ignore because it saturates the rafter tails.

Before

After

Replacement Cost & What’s Included

In Pompano Beach, Jerith panel replacement falls within our standard roof repair range of $400-$1,800 for localized work, or $8,000-$20,000 if the full roof system has reached end of life. A typical panel swap runs $600-$2,500 depending on access height, whether the damaged panel is in the field or at a valley, and if the underlying plywood needs replacement. We itemize every line: aluminum panel by the square foot, compatible fasteners with neoprene washers, new butyl tape at all laps, and foam closures at the ridge. Under Clause 1 of the Haven Standard, you get that written price before anyone touches a ladder. Our 365-Day Done Right Promise covers the installation and the materials we supply. Every visit includes a documented photo record of the damage, the repair, and the finished condition.

DIY or Call Us?

A homeowner can safely check the panel code from a stepladder and photograph the damage for us to review. What you should not do is walk on an aluminum roof. The panels dent underfoot, the ribs are a trip hazard, and a wet aluminum surface has the friction coefficient of wet ice. Removing a single panel without disturbing the adjacent ones requires a specialized unlock tool and a feel for the snap-lock engagement that comes from doing it hundreds of times. We’ve been called to Pompano Beach homes where a well-intentioned owner bent three good panels trying to free one bad one. The call to fix the original problem plus the collateral damage costs more than calling first. If you’re unsure, text us photos and we’ll tell you what we’re seeing.

FAQs