Therma-Tru Roofing Nationwide

Therma-Tru Roofing: The Pompano Beach Owner’s Guide

Therma-Tru roofing components in Pompano Beach typically run $400-$1,800 for repair and $8,000-$20,000 for full replacement, with most common flashing and seal failures addressed same-day when we have the part on the truck. We stock Therma-Tru-compatible edge metal, step flashing, and membrane termination bars for the coastal Florida climate, and we carry matching color samples from the Classic-Craft, Fiber-Classic, and Smooth-Star series lines. Most Pompano Beach owners discover a problem when they spot rust streaking down a wall after a summer storm, or when a musty smell starts in a closet that shares a wall with a dormer - the kind of slow leak that doesn’t show on the ceiling until the drywall is already soft.

Call (754) 714-6540

Which Therma-Tru Models This Applies To

Therma-Tru doesn’t manufacture complete roofing systems; they produce entry door systems, sidelites, and transoms that integrate with roofing at the head flashing and wall-to-roof junction. The parts we stock and install are the roofing interface components that fail where a Therma-Tru door unit meets the roofline - specifically the head flashing pan, end dams, and membrane termination bars for door units in gable-end walls and shed-roof additions.

To identify what you need, check the silver label on the door hinge edge for the series name and the date code. Classic-Craft and Fiber-Classic units from 2012-2019 used a 2-inch head flange that requires a 4-inch minimum flashing height; Smooth-Star and newer Fiber-Classic units moved to a 2.5-inch flange that pairs with standard 6-inch step flashing. The critical gotcha: mixing a 2-inch flange with 6-inch flashing leaves a gap at the end dams that traps salt air and accelerates corrosion in Pompano Beach’s coastal zone. We stock both OEM Therma-Tru flashing kits and quality aftermarket equivalents from Tamlyn and Berridge that meet the same 0.032-inch aluminum spec; the aftermarket parts save roughly 15 percent and carry the same 20-year finish warranty in our experience.

Signs Your Therma-Tru Roofing Is Failing

• Rust streaks below the door head or sidelite. This means the galvanized or aluminum flashing has breached at the end dam or the sealant bed has dried out. In Pompano Beach, the salt-laden onshore flow accelerates this by a factor of two compared to inland Broward County - we see it most often on east-facing elevations within a mile of the Intracoastal.
• Soft drywall in the interior corner near a Therma-Tru unit. Water is traveling along the top plate or down the stud bay, usually because the head flashing was not lapped correctly over the housewrap. The leak can run 4-6 feet sideways before it finds an exit, so the damage rarely aligns with the door itself.
• Peeling paint or efflorescence on exterior trim below the roofline. This indicates capillary action at the flashing-to-membrane joint, common where the original installer used a non-compatible sealant or skipped the back dam on the head pan. The Therma-Tru installation manual calls for a continuous bead of polyurethane sealant; silicone or butyl tapes break down in UV within 18 months here.
• Visible gaps between the door frame and siding after settling. Florida’s sandy soils and seasonal moisture swings cause frame movement; if the flashing wasn’t installed with adequate slack or expansion joints, the metal fatigue-cracks at the corner folds. We find this on about one in three older Pompano Beach homes we inspect near the historic Old Town district.
• Insect intrusion in the header area. Once water compromises the flashing, the damp wood attracts carpenter ants and termites. If you’re seeing frass or winged insects near a Therma-Tru unit, the roofing interface has likely been breached for months.

Before

After

Replacement Cost & What’s Included

The range depends on three factors: whether we can work from a ladder or need staging, how many courses of roofing must be disturbed to lap the new flashing correctly, and whether the door unit itself must be pulled to address rot in the rough opening. Under Clause 1 of the Haven Standard, we deliver a written line-item price before any work starts - parts, labor, permit fees if applicable, and the documented photo record included as standard. Our 365-Day Done Right Promise covers the workmanship; material warranties run 20 years on finish and 10 years on structural integrity for the flashing components we install.

DIY or Call Us?

There’s a short list of checks any Pompano Beach homeowner can make safely: confirm the leak aligns with a door unit by running a hose at the head and watching for interior moisture, photograph the rust pattern for our crew to review, and verify the door series from the hinge label so we bring the right flashing profile. What you should not attempt is removing roofing material, disturbing the head flashing, or working on a ladder above single-story height. The head pan on a Therma-Tru unit is structural to the water management; if you break the sealant bond without a replacement plan, you’re exposing the rough opening to the next rain. We’ve rebuilt more than one well-intentioned DIY repair in Pompano Beach where the owner saved $200 on labor and spent $1,800 on rot repair six months later. Call (754) 714-6540 and we’ll schedule a free estimate with a written price before anyone picks up a tool.

FAQs