Boral Driveway & Pavers Nationwide

Boral Driveway & Pavers: The Pompano Beach Owner’s Guide

We stock and install Boral-compatible driveway and paver systems in Pompano Beach, with paver driveway installation typically running $7,000-$18,000 and concrete driveway installation at $4,500-$12,000 depending on substrate condition and pattern complexity. Most Boral pattern matches and color-lot replacements can be sourced within 24-48 hours through our network of fifty-plus vetted material brands. Homeowners usually discover a failing Boral installation when individual pavers begin rocking underfoot, edge restraints pull away from the bedding course, or surface spalling appears after a heavy rain - the freeze-thaw cycling is minimal in Pompano Beach, but the salt air and seasonal saturation do their own damage.

Call (754) 714-6540

Which Boral Models This Applies To

Boral’s hardscape line in the South Florida market has shifted over the past decade, and identification matters because color lots vary by production year. The common residential series we encounter in Pompano Beach include the Boral Stonegate pavers in the modular 6×6, 6×9, and 6×12 plank formats, and the Boral Plaza pavers in the 4×8 and 8×8 sizes. Newer installations may carry the Boral Versetta Stone or Boral ProStone veneer lines, though these are vertical applications rather than driveway-grade. Check the chamfered edge profile and the back-web pattern: Stonegate carries a three-point contact surface for bedding sand lock, while older Boral Cobble series used a full-flat back that shifts more readily under load.

OEM Boral pavers are no longer manufactured under the original Boral North America hardscape division, which sold its concrete and clay paver operations to Oldcastle APG in 2018. What we call “Boral-compatible” now means matching the dimensional spec, the compressive strength rating (typically 8,000+ PSI for vehicular applications), and the surface texture to blend with existing installations. We source through Belgard, Techo-Bloc, and other vetted brands whose current lines replicate the Boral dimensional profiles. For a seamless repair, we pull a sample paver, measure to the nearest 1/16 inch, and verify the chamfer angle under a straightedge before ordering. Color matching in Pompano Beach’s UV exposure is the harder problem: even “the same” color name from a different year will have shifted after 2,000 hours of Florida sun.

Signs Your Boral Driveway & Pavers Is Failing

• Individual pavers rock or wobble under tire traffic. The bedding sand has washed out or compacted unevenly, often because the joint sand above failed first and allowed water to channel beneath. In Pompano Beach, this accelerates after any landscaping irrigation that oversprays the driveway edge.
• Edge restraints bow outward or pull free from spikes. The flexible PVC or aluminum edging loses its hold when the aggregate base behind it erodes, which happens faster where lawn maintenance crews ride the perimeter with heavy equipment.
• Surface spalling or pitting appears, especially in low spots. Salt air deposits chloride on the paver surface; when water pools and evaporates repeatedly, the cement paste at the surface begins to deteriorate. This is cosmetic at first but deepens to structural loss.
• Weeds or grass grow thickly through joints that were previously tight. The polymeric joint sand has degraded or was never properly installed, leaving voids that collect organic material. Pompano Beach’s growing season runs nearly year-round, so this signals an open pathway for water.
• Visible settlement or low spots forming a birdbath effect. The compacted base - typically 6-8 inches of crushed limestone screenings in our market - has consolidated further or was inadequately compacted during original installation. This is the most expensive failure to correct because it requires lifting, regrading, and relaying.

Before

After

Replacement Cost & What’s Included

Partial Boral paver replacement in Pompano Beach typically falls between $2,500 and $6,500 for a standard two-car driveway section, while full driveway replacement runs $7,000-$18,000. The spread depends on three factors: how many pavers must be lifted to access the failed substrate, whether the base course can be salvaged or must be excavated and recompacted, and the availability of a color-compatible replacement lot.

Our written quote itemizes each layer - demolition and disposal of failed pavers, base inspection and recompaction if needed, bedding sand replacement, paver relay or new installation, polymeric joint sand application, and edge restraint reset or replacement. Under Clause 1 of the Haven Standard, that price is fixed before any work starts; no change proceeds without a signed change order. The 365-Day Done Right Promise covers the installation workmanship, and we document the substrate condition with photos before covering it, included as standard. If we’re matching existing Boral pavers rather than replacing the full field, we flag the color-lot risk in writing so there’s no surprise at the joint line.

DIY or Call Us?

A homeowner can safely inspect what’s failing: photograph the paver pattern from multiple angles, measure a loose paver with a tape measure, and check whether the edge restraint moves by hand pressure. What you find tells us plenty before we arrive. But lifting and relaying pavers without disturbing the surrounding field requires a plate compactor, proper screed rails for the bedding sand, and knowledge of the original base depth - in Pompano Beach, we typically see 6 inches of #57 stone plus 1 inch of coarse bedding sand for residential driveways, but older installations varied. Resetting edge restraints against a live lawn grade without proper drainage backing leads to the same failure in eighteen months. For the documented photo record and a written price before any work starts, call (754) 714-6540.

FAQs